The torque wrench tester of the PCE-TWM series can test torque wrenches up to 500 Nm / 368.78 ft-lb, depending on the sensor. Due to the precise evaluation electronics, the torque wrench tester has a measurement accuracy of 0.5 % of the measurement range. The torque wrench is fixed by means of a 1/4' female square. The torque wrench tester consists of an evaluation unit and an external torque transducer with a cable which makes the measurement setup convenient.

- Measurement range: 500 Nm (50 kgfm) / 368.78 ft-lb
- Resolution: 1 Nm / 0.738 ft-lb
- Accuracy: ±0.5 % of measurement range
- Units of measurement: Nm, Ncm, kgfm, lbfin, gfm
- Calibration: possible with external F2 weights
- Max. overload: 50 % of measurement range

 

The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.

- Measuring range: 10 Nm (1 kgf-m) / 7.38 ft-lb
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm

The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.

- Measuring range: 5 Nm (0,5 kgf-m) / 3.69 ft-lb
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm

 

The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.

- Measuring range: 2 Nm (0,2 kgf-m) / 1.475 ft-lb
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm

 

- Measuring range: 0 ... 50 kN / 50,000 N / 11,240 lbs
- Resolution: 5 N / 1.1 lbs
- Accuracy: ± 0.5% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display

The force gauge PCE-DFG N 50K measures both tensile forces and compressive forces with a very high resolution and sampling rate. The force gauge helps to determine the yield strengths, the tear-off force and is used wherever acting forces have to be documented.

- Measuring range: 0 ... 50 kN / 50,000 N
- Resolution: 5 N
- Accuracy: ± 0.2% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display

The Force Gage PCE-DFG N 50K measures both tensile forces and compressive forces with a very high resolution and sampling rate. The force gage helps to determine the yield strengths, the tear-off force and is used wherever acting forces have to be documented.

- Measuring range: 0 ... 50 kN / 50,000 N
- Resolution: 5 N
- Accuracy: ± 0.2% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display

The Force Gage PCE-DFG N 50K-ICA measures both tensile forces and compressive forces with a very high resolution and sampling rate. The force gage helps to determine the yield strengths, the tear-off force and is used wherever acting forces have to be documented.

- Measuring range: 0 ... 50 kN / 50,000 N
- Resolution: 5 N
- Accuracy: ± 0.2% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display
- Including ISO calibration certificate

The force gauge PCE-DFG N 50K-ICA measures both tensile forces and compressive forces with a very high resolution and sampling rate. The force gauge helps to determine the yield strengths, the tear-off force and is used wherever acting forces have to be documented.

- Measuring range: 0 ... 50 kN / 50,000 N
- Resolution: 5 N
- Accuracy: ± 0.2% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display
- Including ISO calibration certificate

With this videoscope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the videoscope consists of braided tungsten.

- Diameter: Ø2.2mm / 0.08"
- Cable length: 1m / 3.2 ft
- Camera direction: 90°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this videoscope, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the videoscope consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Camera resolution 160,000 pixels each
- Viewing angle front camera 120°, side camera 90°
- Focusing distance 5 … 50 mm / 0.19 ... 1.96" each
- Camera head length: 42 mm / 1.6"
- Bending radius at 90° 35 mm / 1.3"
- Live images from both cameras side by side
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this automotive tester, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the automotive tester consists of braided tungsten.

- Diameter: Ø2.2mm / 0.08"
- Cable length: 1m / 3.2 ft
- Camera direction: 90°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this car measuring device, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the car measuring device consists of braided tungsten.

- Diameter: Ø2.2mm / 0.08"
- Cable length: 1m / 3.2 ft
- Camera direction: 90°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission