Industrial Measurement Products and Solutions
Order no.: PCE-N30H

The digital indicator PCE-N30H can measure direct voltage up to 500 V and direct current up to 5 A. This makes the digital indicator an ideal device, when it comes to monitoring of direct current. The measured values are shown on the large LED display of the PCE-N30H.


- Measuring range: ±100 / ±500 V DC; ±1 /±5 A DC
- Display range: -19,999 ... +99,999
- 21-point scaling
- IP 65 protection on the front

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PS 420

The simple pressure sensor PCE-PS 420 can be used everywhere where simple pressure is to be measured. The measured pressure is provided as a 4 ... 20 mA analog value on the pressure sensor.


- Max. 400 Bar (selectable)
- 4 ... 20 mA output
- Media: non-corrosive gases and liquids
- Pressure: relative
- Diaphragm: Ceramics
- Accuracy class: 1

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PH 22-ICA

The environmental meter is used for fast and accurate detection of pH and temperature. Due to the practical double display, both values ​​can be read simultaneously on the environmental meter.


- Measuring range: 0.0 ... 14.0 pH
- Resolution: 0.01 pH
- Accuracy: ± 0.02 pH
- 100 points Datalogger
- (ATC) in the range 0 ... 80°C / 32 ... 176°F
- Waterproof to IP 67
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PH 22-ICA
The environmental tester is used for fast and accurate detection of pH and temperature. Due to the practical double display, both values ​​can be read simultaneously on the environmental tester.


- Measuring range: 0.0 ... 14.0 pH
- Resolution: 0.01 pH
- Accuracy: ± 0.02 pH
- 100 points Datalogger
- (ATC) in the range 0 ... 80°C / 32 ... 176°F
- Waterproof to IP 67
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-LPS 1305
The Laboratory Power Supply is a completely newly designed, linearly regulated laboratory power supply in a modern design and with the latest technology. The desktop power supply supports a voltage range of 0 ... 30 V and a current range of up to 5 A DC. Thanks to the 3-digit blue 14 mm LED display for voltage and current values, a quick and precise reading from the desktop power supply is possible.

- for voltages up to 30 V and 5 A.
- 2 displays for current and voltage
- Output can be switched off separately
- Overload protection, short-circuit proof
- higher efficiency for better effectiveness
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PH 22-ICA

The waterproof Swimming Pool pH meter is used for fast and accurate measurement of pH and temperature. Due to the practical double display, both values can be read simultaneously on the pH meter. The waterproof and robust housing (IP 67) means the pH meter can be used under difficult conditions.

- Measuring range: 0.0 ... 14.0 pH
- Resolution: 0.01 pH
- Accuracy: ± 0.02 pH
- 100 points Datalogger
- (ATC) in the range 0 ... 80°C / 32 ... 176°F
- Waterproof to IP 67
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PH 22-ICA
The water analysis meter is used for fast and accurate detection of pH and temperature. Due to the practical double display, both values ​​can be read simultaneously on the water analysis meter.


- Measuring range: 0.0 ... 14.0 pH
- Resolution: 0.01 pH
- Accuracy: ± 0.02 pH
- 100 points Datalogger
- (ATC) in the range 0 ... 80°C / 32 ... 176°F
- Waterproof to IP 67
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FST-200-201-I

The air flow meter is compatible with and can be mounted on to a wide variety of available measuring equipment. The sensor will detect even the minutest movements of air and the results are then output in analogue form.


- Output signal: 4 … 20-mA
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0.5 m/s … 50 m/s (1.1 ... 111.8 mph)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FST-200-201-U

The air flow meter is compatible with and can be mounted on to a wide variety of available measuring equipment. The sensor will detect even the minutest movements of air and the results are then output in analogue form.


- Output signal: 0 … 10V
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0.5 m/s … 50 m/s (1.1 ... 111.8 mph)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FST-200-202-I

The air flow meter measures the direction of wind and the results are then output in analogue form. The sensor is compatible with and can be mounted on to a wide variety of available measuring equipment.


- Output signal: 4 … 20-mA
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0 … 360°

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FST-200-202-U

The air flow meter measures the direction of wind and the results are then output in analogue form. The sensor is compatible with and can be mounted on to a wide variety of available measuring equipment.


- Output signal: 0 … 10V DC
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0 … 360°

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-ERT 10

This PCE-ERT 10 earth tester is a handy device which allows fast and easy determination of the earth resistance. The grounding resistance is determined with this earth tester in three measuring ranges up to 2000 Ω using three-wire technology.


- Three-wire measuring method
- Earth resistance is determined in three measuring ranges
- Ground voltage measurement up to 200 V
- Zeroing possible
- Alternating and DC voltage measurement

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-127

A DIN flow cup meter is a viscometer to determine the toughness of liquids. It is commonly used in the industrial sector as well as in research laboratories. However, only low-viscosity liquids can be measured by means of this method as liquids cannot pass through the nozzles if their viscosity is too high.


- Capacity 100 ml
- With overflow gutter
- Meets international standards
- 2 editions available (flow or immersion cup)

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-128

The PCE-128 ISO / ASTM viscometer or ISO / ASTM Flow Cup Meter uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, an ISO / ASTM cup is used to determine the kinematic viscosity of fluids. The structure of an ISO / ASTM Flow Cup Meter is standardized according to BS EN ISO 2431 / ASTM D5125. Designed for use with Newtonian and near-Newtonian liquids, this Flow Cup Meter series features:


- Orifice diameters (Ø) of 3 mm, 4 mm, 5 mm, 6 mm, or 8 mm / 0.12 in, 0.16 in,
  0.20 in, 0.24 in, or 0.31 in

- Viscosity ranges of 7 ... 42, 34 ... 135, 91 ... 326, 188 ... 684 or 600 ... 2,000 cSt /
  mm²/s
- Flow times of 25 ... 150 or 30 ... 100 seconds (s)

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-127

The PCE-127 DIN flow cup viscometer or DIN immersion viscosity flow cup series uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, a DIN flow cup is used to determine the kinematic viscosity of fluids. The structure of a DIN flow cup is standardized according to DIN 53211. Designed for use with Newtonian and near-Newtonian liquids, this viscosity cup series features:


- Orifice diameter (Ø) of 4 mm
- Viscosity range of 96.2 ... 680 mPa.s / cP
- Flow time of 25 ... 150 seconds

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-128

The PCE-128 ISO / ASTM viscometer or ISO / ASTM Flow Cup Viscometer uses gravity to measure the flow rate of a liquid. Under ideal conditions, flow rate is proportional to kinematic viscosity. Thus, an ISO / ASTM cup is used to determine the kinematic viscosity of fluids. The structure of an ISO / ASTM Flow Cup Viscometer is standardized according to BS EN ISO 2431 / ASTM D5125. Designed for use with Newtonian and near-Newtonian liquids, this Flow Cup Viscometer series features:
- Orifice diameters (Ø) of 3 mm, 4 mm, 5 mm, 6 mm, or 8 mm / 0.12 in, 0.16 in, 0.20 in, 0.24 in, or 0.31 in
- Viscosity ranges of 7 ... 42, 34 ... 135, 91 ... 326, 188 ... 684 or 600 ... 2,000 cSt / mm²/s
- Flow times of 25 ... 150 or 30 ... 100 seconds (s)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-LED 20

PCE-LED 20 is a light meter with an external LED light sensor. The cable of the LED light sensor has a length of approximately 1.5 m / 4.9 ft.


- Measuring range: 40 / 400 / 4000 / 40000 / 400000 lx or fc
- Measuring units (selectable): Lux (lx) or footcandle (fc)
- Accuracy: ± 3% (with a standard incandescent lamp at 2856 K and LED white light), ± 6% for other visible light sources

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-LED 20

PCE-LED 20 is a lux meter with an external LED light sensor. The cable of the LED light sensor has a length of approximately 1.5 m / 4.9 ft.


- Measuring range: 40 / 400 / 4000 / 40000 / 400000 lx or fc
- Measuring units (selectable): Lux (lx) or footcandle (fc)
- Accuracy: ± 3% (with a standard incandescent lamp at 2856 K and LED white light), ± 6% for other visible light sources

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FST-200-201-I

The wind speed sensor is compatible with and can be mounted on to a wide variety of available measuring equipment. The sensor will detect even the minutest movements of air and the results are then output in analogue form.


- Output signal: 4 … 20-mA
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0.5 m/s … 50 m/s (1.1 ... 111.8 mph)

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FST-200-201-U

The wind speed sensor is compatible with and can be mounted on to a wide variety of available measuring equipment. The sensor will detect even the minutest movements of air and the results are then output in analogue form.


- Output signal: 0 … 10V
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0.5 m/s … 50 m/s (1.1 ... 111.8 mph)

 

Manufacturer: PCE Instruments
Test Instruments manufacturer