Order no.: PCE-TAT 10

The simple design and an absolutely straightforward operation make it possible for the practitioner to use the adhesion tester as an instrument for daily adhesion tests. Using adhesive with rapid curing, the tests can be performed by the user in the shortest possible time.


- Breakout force: 200 kg
- Diameter of base dolly, mm: 15.1 (№ 1) and 19.5 (№ 2)
- Specific breakout force, MPa: Dolly №1 up to 10 MPa (100) Dolly
  №2 up to 6 MPa (60)

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: 844

This ring force gauge allows you to record and display the axial and bearing forces. The display of the ring force gauge is a very accurate and large dial gauge, scaled in kN.


- Measuring range 0 N ... 1000 kN (depending on model)
- For measuring axial and bearing forces
- Made of stainless steel
- Display in Kilonewton


Please make your selection in the technical data or in the shopping cart.

Manufacturer: Erichsen GmbH & Co. KG
Test Instruments manufacturer
Order no.: Xgard-1-O3

The Xgard-1-O3 is a single-gas Gas Leak Detector used to warn for gases (Ozone, O3, 0 ... 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Ozone, O3, 0 ... 1 ppm)
- Additional display and alarm station
- ATEX or UL approval

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: PCE-RT 10-ICA

The Material Surface Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

 

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate


 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RT 10-ICA

The Profilometer Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.


- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate


 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RT 10-ICA

The Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.


- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RT 10-ICA

The Surface Testing Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.



- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: TXgard-IS+H2S

The TXgard-IS+H2S is a single-gas Gas Leak Detector used to warn for gases (Hydrogen Sulfide, H2S, 0 ... 50 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).


- Stationary
- For Hydrogen Sulfide, H2S, 0 ... 50 ppm
- Additional display and alarm station
- ATEX or UL approval

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: Xgard-1-O3

The Xgard-1-O3 is a single-gas Gassensor used to warn for gases (Ozone, O3, 0 ... 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Ozone, O3, 0 ... 1 ppm)
- Additional display and alarm station
- ATEX or UL approval

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: TXgard-IS+H2S

The TXgard-IS+H2S is a single-gas Gas Leak Detector used to warn for gases (Hydrogen Sulfide, H2S, 0 ... 50 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).


- Stationary
- For Hydrogen Sulfide, H2S, 0 ... 50 ppm
- Additional display and alarm station
- ATEX or UL approval

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: PCE-PGM 100-ICA

The PCE-PGM 100 gloss meter works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the gloss meter emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.


- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PGM 100-ICA

The PCE-PGM 100 Surface Testing works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the Surface Testing emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.


- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU 
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: TXgard-IS+CO

The TXgard-IS+CO is a single-gas Gas Leak Detector used to warn for gases (Carbon Monoxide, CO, 0 ... 500 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).


- Stationary
- For Carbon Monoxide, CO, 0 ... 500 ppm
- Additional display and alarm station
- ATEX or UL approval

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: PCE-428-Kit

The PCE-428-KIT Sound Level Meter Kit is commonly used by professionals to ensure compliance with environmental noise regulations and workplace noise permissible exposure limits. The sound level meter also functions as a data logger, recording measurements at an adjustable interval from 1 s ... 24 h and storing the recorded measurement data to a micro SD card memory. Alternatively, the sound level meter can be connected directly to a PC via USB.

- Class 2
- Measuring range: 25 ... 136 db(A)
- LXY (SPL), Leq (LXeq), LXYSD, LXSEL, LXE, LXYmax, LXYmin, LXPeak, LXN
- Frequency weighting: A, B, C and Z
- Time weighting: Fast (125 ms), slow (1 sec) and impulse (35 ms), decay (1500 ms)
- adjustable data-recording interval from 1 s ... 24 h
- 1/1 octave band filter (optional 1/3 octave band filter upgrade)
- Kit includes factory calibration certificates (per ISO 9001) and a type 2 / class 2 acoustic calibrator (PCE-SC 42)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-428-Kit

PCE-428-KIT is a class 2 data-logging condition monitoring noise meter kit that meets IEC 60651:1979, IEC 60804:2000, IEC 61672-1:2013, ANSI S1.4-1983 and ANSI S1.43-1997 requirements. This portable high-accuracy sound level meter has a large easy-to-read illuminated LCD screen that displays the sound pressure level (SPL) numerically and graphically in real time.

- Measuring range: 25 ... 136 db(A)
- A, B, C and Z frequency weightings
- Time weighting: Fast (125 ms), slow (1 sec) and impulse (35 ms), decay (1500 ms)
- Adjustable data-recording interval from 1 s ... 24 h
- 1/1 octave band filter (optional 1/3 octave band filter upgrade)
- Kit includes factory calibration certificates (per ISO 9001) and a type 2 / class 2 acoustic calibrator (PCE-SC 42)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-428-Kit

PCE-428-KIT is a class 2 data-logging noise meter / sound meter kit that meets IEC 60651:1979, IEC 60804:2000, IEC 61672-1:2013, ANSI S1.4-1983 and ANSI S1.43-1997 requirements. This portable high-accuracy sound level meter has a large easy-to-read illuminated LCD screen that displays the sound pressure level (SPL) numerically and graphically in real time.

- Measuring range: 25 ... 136 db(A)
- A, B, C and Z frequency weightings
- Time weighting: Fast (125 ms), slow (1 sec) and impulse (35 ms), decay (1500 ms)
- Adjustable data-recording interval from 1 s ... 24 h
- 1/1 octave band filter (optional 1/3 octave band filter upgrade)
- Kit includes factory calibration certificates (per ISO 9001) and a type 2 / class 2 acoustic calibrator (PCE-SC 42)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-428-Kit

PCE-428-KIT is a class 2 sound data logger kit that meets IEC 60651:1979, IEC 60804:2000, IEC 61672-1:2013, ANSI S1.4-1983 and ANSI S1.43-1997 requirements. This portable high-accuracy sound level meter has a large easy-to-read illuminated LCD screen that displays the sound pressure level (SPL) numerically and graphically in real time.

- Measuring range: 25 ... 136 db(A)
- A, B, C and Z frequency weightings
- Time weighting: Fast (125 ms), slow (1 sec) and impulse (35 ms), decay (1500 ms)
- Adjustable data-recording interval from 1 s ... 24 h
- 1/1 octave band filter (optional 1/3 octave band filter upgrade)
- Kit includes factory calibration certificates (per ISO 9001) and a type 2 / class 2 acoustic calibrator (PCE-SC 42)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MA 200

The absolute moisture meter PCE-MA 200 is used to weigh a range of substances up to 200g / 7.05oz and measure their moisture content. A halogen lamp heats up the chamber to 199 °C / 390 °F. The absolute moisture meter dries the substance to be weighed within the heating chamber and determines the moisture content from the difference in weight.


- Testing or weighing capacity: 200 g / 7.05 oz
- Readability: 1 mg / 0.001 g / 0.01 %
- Adjustable drying temperature and time
Accuracy to 0.01 %

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MA 200

The analytical balance PCE-MA 200 is used to weigh a range of substances up to 200g / 7.05oz and measure their moisture content. A halogen lamp heats up the chamber to 199 °C / 390 °F. The analytical balance dries the substance to be weighed within the heating chamber and determines the moisture content from the difference in weight.


- Testing or weighing capacity: 200 g / 7.05 oz
- Readability: 1 mg / 0.001 g 
- Adjustable drying temperature and time
Accuracy to 0.01 %

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MA 200

The benchtop scale PCE-MA 200 is used to weigh a range of substances up to 200g / 7.05oz and measure their moisture content. A halogen lamp heats up the chamber to 199 °C / 390 °F. The benchtop scale dries the substance to be weighed within the heating chamber and determines the moisture content from the difference in weight.


- Testing or weighing capacity: 200 g / 7.05 oz
- Readability: 1 mg / 0.001 g / 0.01 %
- Adjustable drying temperature and time 
Accuracy to 0.01 %

 

Manufacturer: PCE Instruments
Test Instruments manufacturer