Order no.: AQ-200 Set OZU

Gas Detector AQ-200 is a highly accurate instrument for measuring ozone concentrations in the air. The Gas Detector can be equipped with four different heads that vary in their measurement range.


- High accuracy and functionality
- Interchangeable sensor heads!
- Battery operation
- Sensor head OZU included in delivery (Ozone 0-0.15 ppm)

 

Manufacturer: Aeroqual
Test Instruments manufacturer
Order no.: PCE-SGM 60

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This gloss meter allows you to measure very high gloss surfaces above 70 gloss units (GU).


- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-SGM 60
The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. These gloss test instruments allow you to measure very high gloss surfaces above 70 gloss units (GU).


- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: AQ-200 Set OZU

Ozone Meter AQ-200 is a highly accurate instrument for measuring ozone concentrations in the air. The Ozone Meter can be equipped with four different heads that vary in their measurement range.


- High accuracy and functionality
- Interchangeable sensor heads!
- Battery operation
- Sensor head OZU included in delivery (Ozone 0-0.15 ppm)

 

Manufacturer: Aeroqual
Test Instruments manufacturer
Order no.: PCE-SGM 60

The PCE-SGM 60 surface tester and gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This meter allows you to measure very high gloss surfaces above 70 gloss units (GU).


- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: Xgard-1-Cl2

The Xgard-1-CL2 is a single-gas Gas detector used to warn for gases (Chlorine, CL2, 0 ... 5 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).


- Stationary
- For (Chlorine, CL2, 0 ... 5 ppm)
- Additional display and alarm station
- ATEX or UL approval

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: PCE-RT 10

The Material Surface Roughness Tester PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.


- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.02 to 100um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RT 10

The Roughness Tester PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.


- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RT 10

The Surface Profilometer PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.


- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RT 10

The Surface Testing Roughness Tester PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.


- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DDM 3WI-ICA

The PCE-DDM 3WI-ICA Crane Scale is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 3WI-ICA Crane Scale is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.


- Measurement range: 3,000 kg / 30 kN / 6,614 lbs
- Resolution: 1 kg / 10 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied without remote control / indicator
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DDM 3WI-ICA

The PCE-DDM 3WI-ICA Hanging Scale is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 3WI-ICA Hanging Scale is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.


- Measurement range: 3,000 kg / 30 kN / 6,614 lbs
- Resolution: 1 kg / 10 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied without remote control / indicator
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DDM 3WI-ICA

The PCE-DDM 3WI-ICA Weighing Hook is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 3WI-ICA Weighing Hook is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.


- Measurement range: 3,000 kg / 30 kN / 6,614 lbs
- Resolution: 1 kg / 10 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied without remote control / indicator
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GPA 62-ICA

This clamp meter is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The clamp meter is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GPA 62-ICA

This clamp on tester is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The clamp on tester is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GPA 62-ICA

This current clamp is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The current clamp is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GPA 62-ICA

This HVAC meter is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The HVAC meter is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GPA 62-ICA

This 1-Phase-Power Meter is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyzer clamp is equipped with data logger. The test instrument is delivered manufacturer ISO calibrated.


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Records up to 50,000 records
incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GPA 62-ICA

This power analyzer is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyzer clamp is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GPA 62-ICA

This power datalogger is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyzer clamp is equipped with data logger. The test instrument is delivered manufacturer ISO calibrated.

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer