Industrial Measurement Products and Solutions
Order no.: PCE-C-R1S

Due to its ball bearing, the load cell has a special resistance against lateral forces. The load cell has a strong output signal of approx. 4 mV / V and works with a measurement uncertainty of 0.03% F.S.. The load cell is used especially in harsh environments such as truck scales, train scales, machine weighing, etc..

- Rated load / force F.S.: 0.5 t ... 100 t / 5 kN ... 1 MN
- Corrosion resistant IP67
- Bearing surface ball bearing
- 700 Ohm

 

- Force sensor nominal load selectable! If require 50 t or 100 t please select variant.

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-C-R6S

The flat load cell offers optimum force transmission thanks to its low height and large support surface. The load cell is used especially where there is no space for a complete weighing module. The load cell consists of two components, the lower part being conical and thus able to compensate for smaller tilting movements.

- Rated load / force F.S.: 500 ... 5000 kg / 5000 ... 50000 N
- Corrosion resistant IP67
- 6-wire technology

 

- Force sensor nominal load selectable!

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DX-AS-ICA

Mechanical shore durometer for measuring hardness of soft elastomer with drag needle. The shore durometer is composed of a single component with a measuring head and a 360º dial. To improve the readability of peak value, the device comes with a drag needle, that ensures the maximum reading can be captured. Once it has been measured, it can be reset to zero. 


- Force of pressure: 0 to 12.5 N
- Penetrating body: 35º (according to Shore A)
- Equipped with drag needle
- Measurement range: 10 ... 90
  (pressure diminishes below 10 and above 90)
- Margin of error: ± 1
- Division of scale: 1
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DX-AS-ICA

Mechanical shore hardness tester for measuring hardness of soft elastomer with drag needle. The shore hardness tester is composed of a single component with a measuring head and a 360º dial. To improve the readability of peak value, the device comes with a drag needle, that ensures the maximum reading can be captured. Once it has been measured, it can be reset to zero. 


- Force of pressure: 0 to 12.5 N
- Penetrating body: 35º (according to Shore A)
- Equipped with drag needle
- Measurement range: 10 ... 90
  (pressure diminishes below 10 and above 90)
- Margin of error: ± 1
- Division of scale: 1
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FWS 20N-2

This weather station with outside sensor is a real all-rounder. The wireless weather station with outside sensor is easy to assemble based on the instructions provided. You do not have to be a professional to operate the wireless weather station and outside sensors. The weather data of the weather station with outside sensor for different parameters are sent up to 100 meters by radio signal to the main station.


- 3 displays
- Indoor temperature in Celsius or Fahrenheit
- Outside temperature in Celsius or Fahrenheit
- Indoor air humidity / outdoor air humidity
- Air pressure gauge in inHg or hPa
- Absolute or relative air pressure display selectable
- Precipitation indication in mm or inch
- Precipitation indicator for 1 hour, 24 hours, 1 week, 1 month
- Wind speed in mph, km / h, m / s, knots ...
- Wind direction indicator
- Wind chill temperature gauge
- Weather forecast, trend indicator, storm warning
- and much more...

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HS 50N-ICA

PCE-HS 50N is an affordable digital hanging scale, crane scale, weighing hook or electronic balance that offers quick, easy and accurate weighing of large objects, animals, fish and game. Simply mount the item to be weighed to the hook or snap hook (both hooks are included). Useful for forklift and industrial applications and as well as recreational fishing and hunting, the PCE-HS 50N digital hanging scale features:


- Weight range up to 50 kg / 110 lbs
- Battery operation (3 x AA 1.5 V batteries provided)
- Auto-off, power-saving function (can be deactivated, if preferred)
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HS 50N-ICA

PCE-HS 50N is an affordable digital hanging scale, crane scale, weighing hook or electronic balance that offers quick, easy and accurate weighing of large objects, animals, fish and game. Simply mount the item to be weighed to the hook or snap hook (both hooks are included). Useful for forklift and industrial applications and as well as recreational fishing and hunting, the PCE-HS 50N digital hanging scale features:


- Weight range up to 50 kg / 110 lbs
- Battery operation (3 x AA 1.5 V batteries provided)
- Auto-off, power-saving function (can be deactivated, if preferred)
- incl. ISO Calibration Certificate 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HS 50N-ICA

PCE-HS 50N is an affordable digital hanging scale, crane scale, weighing hook or electronic balance that offers quick, easy and accurate weighing of large objects, animals, fish and game. Simply mount the item to be weighed to the hook or snap hook (both hooks are included). Useful for forklift and industrial applications and as well as recreational fishing and hunting, the PCE-HS 50N digital hanging scale features:


- Weight range up to 50 kg / 110 lbs
- Battery operation (3 x AA 1.5 V batteries provided)
- Auto-off, power-saving function (can be deactivated, if preferred)
- incl. ISO Calibration Certificate 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CA-MN21

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: lead and isolated Ø 4 mm male plugs
- Output protected against voltage surges

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN38

Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.


- Rated current: 200 A AC
- Output signal: AC voltage
- Output / input ratio: 100 mV / A AC, 10 mV / A AC
- Output: isolated Ø 4 mm female sockets

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN21

Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. diameter 20 mm.


- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: lead and isolated Ø 4 mm male plugs
- Output protected against voltage surges

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-MN38

Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. diameter 20 mm.


- Rated current: 200 A AC
- Output signal: AC voltage
- Output / input ratio: 100 mV / A AC, 10 mV / A AC
- Output: isolated Ø 4 mm female sockets

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: PCE-P30U

The temperature and signal Data Logger with memory PCE-P30U has a wide range of applications. Besides converting various signals, the Data Logger can be used with memory for easy data logging tasks. The Data Logger PCE P30U has an SD memory card and is suitable for use with SD and SDHC cards. These logging test instruments are calibrated by the manufacturer. An ISO calibration certificate is available as an option.


- SD memory card and internal memory
- Universal input
- Output galvanically isolated
- Alarm relay
- Memory size of 534,336 sets of data (internal memory)
  Option: SD card 2 GB

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: TD 100

(with 1 roll of thermal paper and 4 batteries) for direct printing of the results (eg for documentation of measuring data on location).

Paper type: Thermal paper

Paper width: 57 mm

Test Instruments manufacturer
Order no.: PCE-320

With the PCE-320 Air Humidity Meter it is possible to measure climate conditions such as temperature and relative humidity, as well as determining surface temperature of objects simultaneously by using the included external temperature sensor or using an infrared measurement. The Air Humidity Meter offers features such as average value, maximum, minimum, and hold functions at a reasonable price.


- Internal probe

- Temperature: -20°C ... 60°C / -4 ... 140°F
- Relative humidity: 10 ... 90% r.H.
- Temperature of global: -22°C ... 60°C / -8 ... 140°F
- Humidity: -68°C ... 60°C / -90 ... 140°F
- Dew point temperature: depending on the sensor

- External probe
- Temperature: -50° C ... 500° C / -58 ... 932°F

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RCM 15
The air humidity meter PCE-RCM 15 is specially designed to monitor the quality of indoor air. Among other things, the air humidity meter measures the parameters for PM1, PM2.5, PM10, TVOC, formaldehyde, humidity and temperature. 

Measured quantity:
- Formaldehyde: 0 ... 1,999 mg / m³
- TVOC: 0 ... 9,999 mg / m³
- PM1, PM2.5, PM10: 0 ... 999 μg / m³
- Temperature: -10 ... 45°C / 14 ... 113°F (Only displays in °C) 
- Humidity: 20 ... 99% RH
- 3 different display modes
- Alarm function
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RCM 15
The air quality meter PCE-RCM 15 is specially designed to monitor the quality of indoor air. Among other things, the air quality meter measures the parameters for PM1, PM2.5, PM10, TVOC, formaldehyde, humidity and temperature. 

Measured quantity:
- Formaldehyde: 0 ... 1,999 mg / m³
- TVOC: 0 ... 9,999 mg / m³
- PM1, PM2.5, PM10: 0 ... 999 μg / m³
- Temperature: -10 ... 45°C / 14 ... 113°F (Only displays in °C) 
- Humidity: 20 ... 99% RH
- 3 different display modes
- Alarm function
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CAL-SH5-Z
[more]
Manufacturer: Exova Metech GmbH ( Caldi )
Test Instruments manufacturer
Order no.: PCE-320

With the PCE-320 Climate Meter it is possible to measure climate conditions such as temperature and relative humidity, as well as determining surface temperature of objects simultaneously by using the included external temperature sensor or using an infrared measurement. The Climate Meter offers features such as average value, maximum, minimum, and hold functions at a reasonable price.


- Internal probe

- Temperature: -20°C ... 60°C / -4 ... 140°F
- Relative humidity: 10 ... 90% r.H.
- Temperature of global: -22°C ... 60°C / -8 ... 140°F
- Humidity: -68°C ... 60°C / -90 ... 140°F
- Dew point temperature: depending on the sensor

- External probe
- Temperature: -50° C ... 500° C / -58 ... 932°F

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-T390

The PCE-T390 Condition Monitoring Thermometer is a digital device with four input channels for type K and type J temperature sensors and two input channels for PT100 temperature sensors. The PCE-T390 Condition Monitoring Thermometer has a SD card slot (from 1 ... 16 GB) for storing the measured data. The data is stored in xls format on the SD card of the contact thermometer so that no additional software is needed for further analysis.


- 4 input channels for type-K, J temperature sensors
- 2 input channels for Pt100 temperature sensors
- 2 x type-K TF-500 temperature sensors are included in the package
- SD card memory (1 ... 16 GB)

 

Manufacturer: PCE Instruments
Test Instruments manufacturer