PCE-HVAC 3 is a multifunction air humidity meter, tester or diagnostic measuring device used for indoor climate and environmental monitoring. In addition to measuring relative humidity and ambient room / dry-bulb temperature, the meter calculates dew-point and wet-bulb temperatures in degrees Celsius (°C) and Fahrenheit (°F). Thus, heating, ventilation and air conditioning (HVAC) installations and HVAC system performance assessments are key applications of the air humidity meter.

- Relative humidity measuring range: 0 ... 100% RH
- Ambient / dew-point temp. range: -30 ... 100°C / -22 ... 212°F
- Wet-bulb temp. range: 0 ... 80°C / 32 ... 176°F

 

The air velocity meter has a measuring range of up to 0 ... 30 m/s. In addition to the velocity, the air velocity meter can precisely measure the volume flow and temperature. The compact design of the sensors, in combination with the extendable telescopic probe, enable measurements to be taken even in places that are particularly difficult to access.

- Speed: 0.00 ... 30.00 m/s / 0.00 ... 98.42 ft/s
- Volume flow: 0.0 ... 339120.0 m3/h
- Temperature: 0 ... 50 °C / 32 ... 122 °F
- Telescopic probe length: 210 ... 426 mm / 8.2 ... 16.7"
- Telescopic probe diameter: 12 mm / 0.47"

The airflow food / hygiene meter has a measuring range of up to 0 ... 30 m/s. In addition to the velocity, the airflow food / hygiene meter can precisely measure the volume flow and temperature. The compact design of the sensors, in combination with the extendable telescopic probe, enable measurements to be taken even in places that are particularly difficult to access.

- Speed: 0.00 ... 30.00 m/s / 0.00 ... 98.42 ft/s
- Volume flow: 0.0 ... 339120.0 m3/h
- Temperature: 0 ... 50 °C / 32 ... 122 °F
- Telescopic probe length: 210 ... 426 mm / 8.2 ... 16.7"
- Telescopic probe diameter: 12 mm / 0.47"

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

PCE-LD 1 is a portable handheld gas detector used to locate CFC/HFC refrigerant gas leaks. This highly sensitive gas leak detector can locate gas leaks from HVACR refrigeration systems even in areas contaminated by other gases. The gas sensor is located at the end of a 390 mm / 15.35 in flexible goose-neck tube, allowing unique access to hard-to-reach places.

- Adjustable high/low sensitivity:
    6 g/yr or 30 g/yr for R-22 and R-134a
    8 g/yr or 40 g/yr for R404A, R-407C and R-410A

 

- AC / DC current, AC voltage and frequency measurement
- Integrated measuring point illumination
- Non-contact voltage tester
- Automatic range selection
- Forceps opening: 18 mm
- Automatic switch-off
- Incl. ISO calibration certificate

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

- AC / DC current, AC voltage and frequency measurement
- Integrated measuring point illumination
- Non-contact voltage tester
- Automatic range selection
- Forceps opening: 18 mm
- Automatic switch-off
- Incl. ISO calibration certificate

The configurable universal measuring transducer for electrical signals is a signal doubler and signal converter for process signals. A 4 ... 20-mA and 0 ... 10V DC signal can be applied to the input. The universal measuring transducer has 2 outputs, whereby output 1 can be set to 4 ... 20-mA and output 2 to 4 ... 20-mA or 0 ... 10V DC. It also has quadruple isolation between power supply, input signal, output 1 and output 2.

- Duplicates analog signals
- 4 ... 20-mA and 0 ... 10V
- Quick configuration using 2 buttons
- DIN rail mounting
- Inputs and outputs galvanically isolated
- Power supply 24 ... 250V AC/DC

The current signal converter has an adjustable measuring range of 0… 600 V AC/DC and can therefore measure a wide variety of voltages. For example, it is possible to connect the transmitter to the supply line in order to monitor the applied voltage.

- Measuring range 0 ... 600 V AC/DC
- Active and passive output signal
- Display and keypad for configuration
- Frequency measurement
- DIN rail mounting
- Display

The current signal transducer has an adjustable measuring range of 0… 600 V AC/DC and can therefore measure a wide variety of voltages. For example, it is possible to connect the transmitter to the supply line in order to monitor the applied voltage.

- Measuring range 0 ... 600 V AC/DC
- Active and passive output signal
- Display and keypad for configuration
- Frequency measurement
- DIN rail mounting
- Display

- AC / DC current, AC voltage and frequency measurement
- Integrated measuring point illumination
- Non-contact voltage tester
- Automatic range selection
- Forceps opening: 18 mm
- Automatic switch-off
- Incl. ISO calibration certificate

The DIN-rail measuring instrument has an adjustable measuring range of 0… 600 V AC/DC and can therefore measure a wide variety of voltages. For example, it is possible to connect the transmitter to the supply line in order to monitor the applied voltage.

- Measuring range 0 ... 600 V AC/DC
- Active and passive output signal
- Display and keypad for configuration
- Frequency measurement
- DIN rail mounting
- Display

- AC / DC current, AC voltage and frequency measurement
- Integrated measuring point illumination
- Non-contact voltage tester
- Automatic range selection
- Forceps opening: 18 mm
- Automatic switch-off
- Incl. ISO calibration certificate

The environmental meter has a measuring range of up to 0 ... 30 m/s. In addition to the velocity, the environmental meter can precisely measure the volume flow and temperature. The compact design of the sensors, in combination with the extendable telescopic probe, enable measurements to be taken even in places that are particularly difficult to access.

- Speed: 0.00 ... 30.00 m/s / 0.00 ... 98.42 ft/s
- Volume flow: 0.0 ... 339120.0 m3/h
- Temperature: 0 ... 50 °C / 32 ... 122 °F
- Telescopic probe length: 210 ... 426 mm / 8.2 ... 16.7"
- Telescopic probe diameter: 12 mm / 0.47"

PCE-HVAC 3 is a multifunction environmental meter, tester or diagnostic measuring device used for indoor climate and environmental monitoring. In addition to measuring relative humidity and ambient room / dry-bulb temperature, the meter calculates dew-point and wet-bulb temperatures in degrees Celsius (°C) and Fahrenheit (°F). Thus, heating, ventilation and air conditioning (HVAC) installations and HVAC system performance assessments are key applications of the PCE-HVAC 3 meter.

- Relative humidity measuring range: 0 ... 100% RH
- Ambient / dew-point temp. range: -30 ... 100°C / -22 ... 212°F
- Wet-bulb temp. range: 0 ... 80°C / 32 ... 176°F

 

PCE-LED 20 is a environmental meter with an external LED light sensor. The cable of the LED light sensor has a length of approximately 1.5 m / 4.9 ft.

- Measuring range: 40 / 400 / 4000 / 40000 / 400000 lx or fc
- Measuring units (selectable): Lux (lx) or footcandle (fc)
- Accuracy: ± 3% (with a standard incandescent lamp at 2856 K and LED white light), ± 6% for other visible light sources