Industrial Measurement Products and Solutions
Order no.: HTGS-10N

Torque meter with separate force transducer for measuring the torque of fasteners, components, switches, drive shafts etc. Handset for cordless and power operation with readings memory and interface. Torque meter with digital output for data processing on the PC.


- Range: 0 ... 10.00 Nm (1000.0 cNm)
- Resolution: 0.01 Nm (1 cNm)
- Torque gauge for fast, accurate measurements
- High repeatability
- Easy handling

 

Manufacturer: Hans Schmidt & Co. GmbH
Test Instruments manufacturer
Order no.: HTGS-2N

The torque meter is a hand-held device for battery and power operation with readings memory and interface for measuring the torque of fasteners, components, switches, drive shafts, etc. The torque meter has an output for pass / fail testing.


- Range: 0 ... 2.000 Nm (200.0 cNm)
- Resolution: 0.001 Nm (0.1 cNm)
- Torque gauge for fast, accurate measurements
- High repeatability
- Easy handling

 

Manufacturer: Hans Schmidt & Co. GmbH
Test Instruments manufacturer
Order no.: HTGS-5N

Torque meter with separate force transducer for measuring the torque of fasteners, components, switches, drive shafts etc. Handset for cordless and power operation with readings memory and interface. Torque meter with digital output for data processing on the PC.


- Range: 0 ... 5.000 Nm (500.0 cNm)
- Resolution: 0.001 Nm (0.1 cNm)
- Torque gauge for fast, accurate measurements
- High repeatability
- Easy handling

 

Manufacturer: Hans Schmidt & Co. GmbH
Test Instruments manufacturer
Order no.: PCE-FB 500TW

The torque wrench tester of the PCE-TWM series can test torque wrenches up to 500 Nm, depending on the sensor. Due to the precise evaluation electronics, the torque wrench tester has a measurement accuracy of 0.5 % of the measurement range. The torque wrench is fixed by means of a 1/4' female square. The torque wrench tester consists of an evaluation unit and an external torque transducer with a cable which makes the measurement setup convenient.


- Measurement range: 500 Nm (50 kgfm)
- Resolution: 1 Nm
- Accuracy: ±0.5 % of measurement range
- Units of measurement: Nm, Ncm, kgfm, lbfin, gfm
- Calibration: possible with external F2 weights
- Max. overload: 50 % of measurement range

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FB 10TS

The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.


- Measuring range: 10 Nm (1 kgf-m)
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FB 5TS

The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.


- Measuring range: 5 Nm (0,5 kgf-m)
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-TTM 10

The screw cap torque meter PCE-TTM 5 is used for testing the torque on various kinds of screw caps. That screw cap torque tester determines quickly and with certainty the required expenditure of force for opening and closing screw caps. Therefore the course of the torque test is recorded continuously, so that the results can be evaluated either at the screw cap torque tester itself or on a computer.


- Measurement range: 10 Nm / 1,000 Ncm / 1000 gfm / 100 lbfin
- Measuring resolution: 0.01 Nm / 1 Ncm / 1 gfm / 0.1 lbfin
- Measuring speed up to 1,000 Hz
- For rotation to left or right side

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-TTM 2

The screw cap torque meter PCE-TTM 2 is used for testing the torque on various kinds of screw caps. That screw cap torque tester determines quickly and with certainty the required expenditure of force for opening and closing screw caps. Therefore the course of the torque test is recorded continuously, so that the results can be evaluated either at the screw cap torque tester itself or on a computer.


- Measurement range: 2 Nm / 200 Ncm / 200 gfm / 20 lbfin
- Measuring resolution: 0.001 Nm / 0.1 Ncm / 0.1 gfm / 0.01 lbfin
- Measuring speed up to 1,000 Hz
- For rotation to left or right side

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-TTM 5

The screw cap torque meter PCE-TTM 5 is used for testing the torque on various kinds of screw caps. That screw cap torque tester determines quickly and with certainty the required expenditure of force for opening and closing screw caps. Therefore the course of the torque test is recorded continuously, so that the results can be evaluated either at the screw cap torque tester itself or on a computer.


- Measurement range: 5 Nm / 500 Ncm / 500 gfm / 50 lbfin
- Measuring resolution: 0.001 Nm / 0.1 Ncm / 0.1 gfm / 0.01 lbfin
- Measuring speed up to 1,000 Hz
- For rotation to left or right side

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FB 2TS

The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.


- Measuring range: 2 Nm (0,2 kgf-m)
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FB 2TW

The torque wrench tester of the PCE-TWM series can test torque wrenches up to 500 Nm, depending on the sensor. Due to the precise evaluation electronics, the torque wrench tester has a measurement accuracy of 0.5 % of the measurement range. The torque wrench is fixed by means of a 1/4' female square. The torque wrench tester consists of an evaluation unit and an external torque transducer with a cable which makes the measurement setup convenient.


- Measurement range: 2 Nm (0.2 kgfm)
- Resolution: 0.001 Nm
- Accuracy: ±0.5 % of measurement range
- Units of measurement: Nm, Ncm, kgfm, lbfin, gfm
- Calibration: possible with external F2 weights
- Max. overload: 50 % of measurement range

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FB 5TW

The torque wrench tester of the PCE-TWM series can test torque wrenches up to 500 Nm, depending on the sensor. Due to the precise evaluation electronics, the torque wrench tester has a measurement accuracy of 0.5 % of the measurement range. The torque wrench is fixed by means of a 1/4' female square. The torque wrench tester consists of an evaluation unit and an external torque transducer with a cable which makes the measurement setup convenient.


- Measurement range: 5 Nm (0.5 kgfm)
- Resolution: 0.001 Nm
- Accuracy: ±0.5 % of measurement range
- Units of measurement: Nm, Ncm, kgfm, lbfin, gfm
- Calibration: possible with external F2 weights
- Max. overload: 50 % of measurement range

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-FB 10TW

The torque wrench tester of the PCE-TWM series can test torque wrenches up to 500 Nm, depending on the sensor. Due to the precise evaluation electronics, the torque wrench tester has a measurement accuracy of 0.5 % of the measurement range. The torque wrench is fixed by means of a 1/4' female square. The torque wrench tester consists of an evaluation unit and an external torque transducer with a cable which makes the measurement setup convenient.


- Measurement range: 10 Nm (1 kgfm)
- Resolution: 0.01 Nm
- Accuracy: ±0.5 % of measurement range
- Units of measurement: Nm, Ncm, kgfm, lbfin, gfm
- Calibration: possible with external F2 weights
- Max. overload: 50 % of measurement range

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-TM 80

The Torque Meter PCE-TM 80 with external sensor to measure the static or startup torque moment in screws, components, switches, transmission shafts, etc. The Torque Meter PCE-TM 80 is an affordable solution to easily calibrate and test static torque measurements.


- Range 0 ... 147 Ncm
- Selection of  3 units (Ncm, kgfcm, lbfin)
- Digital output RS-232
- External torque sensor
- Measures startup or static torque, not dynamic torque 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer