Industrial Measurement Products and Solutions
Order no.: PCE-PA 8300

The easy-to-use PCE-PA 8300 Clamp-On Tester is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:


- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 1) 20 A ... 1200 A AC or (Set 2) 30 A ... 3000 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-830-1

The PCE-830 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-830-2

The PCE-830-2 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-830-3

The PCE-830-3 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-3007 flexible amp clamp (3000 A)
- Electrical conductor pick-up: 170 mm / 6.69 in diameter
- Length of electrical conductor: 610 mm / 24.0 in
- Dimensions: 257 mm x 155 mm x 57 mm / 10.1 in x 6.1 in x 2.2 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values - single phase)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-360-ICA

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.


- Voltage range: 50.0 V ... 600.0 V True RMS value
- Current range: 3.0 A ... 999.9 A True RMS value
- Includes clamps, clips, leads, PC software and data cable
- Data logger of 10,000,000 records at 5/10/30/60/120 second interval options
- For measurement in real time and over an extended time period up to 578 days @ 5 second sample rate
incl. ISO Calibration Certificate 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PA 8000

With the PCE-PA 8000 Clamp on Tester you will be able to perform prolonged measurements of electrical properties. The measurement data is saved in xls format on the included SD card to be easily transferred to a computer or laptop for review. The Clamp on Tester comes manufacturer calibrated and can be certified to ISO or UTIL standards as an option.

- Display: 3.7 in / 94 mm LCD (320 x 240 pixels) with LED backlight
- Electrical properties: AC V, AC A, active power, apparent power, power factor, phase angle, power frequency
- Voltage ranges: 10 V ... 600 V AC, automatic range selection
- Measures current up to 1200 A
- Security / Standards: IEC1010CAT III 600V

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-360

The PCE-360 is a Single-Phase Power Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.


- Voltage range: 50.0 V ... 600.0 V True RMS value
- Current range: 3.0 A ... 999.9 A True RMS value
- Includes clamps, clips, leads, PC software and data cable
- Data logger of 10,000,000 records at 5/10/30/60/120 second interval options
- For measurement in real time and over an extended time period up to 578 days @ 5 second sample rate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CA-B102

The CA-B102 Clamp on Tester is designed for fast location of insulation faults. The Clamp on Tester has a maximum diameter up to 112 mm (4.4 in), and can be used with multimeters. Two selectable measuring ranges are available to allow for precise measurement according to DIN VDE 010.
- Dual range: 4 A and 400 A AC
- Large jaw diameter: 112 mm / 4.4 in
- For measurement according to DIN VDE 0100

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: PCE-GPA 62-ICA

This clamp on tester is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The clamp on tester is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CA-D38N

The CA-D38N D Series Clamp on Tester for oscilloscopes has a high-quality iron core with evenly distributed windings. This allows accurate AC current measurement, even at currents up to 3000 A. Due to the rectangular shape, the Clamp on Tester is particularly suitable for busbars and cables with a large cross section. The Clamp on Tester adapter comes manufacturer calibrated with ISO calibration as an option.
- Measuring range: 1 A to 30 A, 1 A to 300 A, 1 A to 3000 A
- Transformer Ratio: 1 A / 1 V, 100 A / 1 V, 1000 A / 1 V
- Connection: BNC

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: PCE-GPA 62

Clamp on Tester with network Analyzer / Clamp on Tester with data logger. The Clamp on Tester (Graphic Power Quality Analyzer) PCE-GPA 62 is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50? of the harmonic waveform. As all test instruments, the Clamp on Tester is delivered manufacturer calibrated (ISO certification is available optional).


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Records up to 50,000 records


Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CA-C160

The Clamp on Tester from the C1XX series for multimeters has a diameter of 52 mm (2.0 in), maximum 1000 A AC, and is designed for power and harmonics measurement. The Clamp on Tester can be connected via 4 mm (0.2 in) safety plugs to a multimeter. It is also possible to connect the Clamp on Tester via the 4 mm (0.2 mm) sockets or the BNC connector to a data acquisition system. The test instrument comes manufacturer calibrated. As all instruments, it can be certified to ISO as an option.
- Measuring range: 100 mA ... 10 A, 100 mA ... 100 A, 1 A ... 1000 A
- Input / Output: 100 mV / 1 A, 10 mV / 1 A, 1 mV / 1 A
- Connection: 4 mm / 0.2 in BNC connector for oscilloscopes
- Output: AC voltage

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-C173

The 4-caliber Clamp on Tester from the C1XX series for multimeters has a diameter of 52 mm (2.0 in), maximum 1000 A AC, and is designed for power and harmonics measurement. The 4-caliber Clamp on Tester can be connected via 4 mm (0.2 in) safety plugs to a multimeter. It is also possible to connect the 4-caliber Clamp on Tester via the 4 mm (0.2 mm) sockets or the BNC connector to a data acquisition system. The test instrument comes manufacturer calibrated. As all instruments, it can be certified to ISO as an option.
- Measuring range: 1 mA ... 1 A, 10 mA ... 10 A, 100 mA ... 100 A, 1 A ... 1000 A
- Transformer Ratio: 1 A / 1 V, 10 A / 1 V, 100 A / 1 V, 1000 A / 1 V
- Connection: 4 mm / 0.2 in male plugs
- Output: AC voltage

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-D35N

The CA-D35N D Series Clamp on Tester for oscilloscopes has a high-quality iron core with evenly distributed windings. This allows accurate AC current measurement, even at currents up to 3000 A. Due to the rectangular shape, the Clamp on Tester is particularly suitable for busbars and cables with a large cross section. The Clamp on Tester adapter comes manufacturer calibrated with ISO calibration as an option.
- Measuring range: 1 A to 1000 A, 1 A to 2000 A, 1 A to 3000 A
- Transformer Ratio: 1 A / 1 mA, 2 A / 1 mA, 3 A / 1 mA
- Connection: 4 mm / 0.2 in socket

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-D32N

The CA-D32N D Series Clamp on Tester for oscilloscopes has a high-quality iron core with evenly distributed windings. This allows accurate AC current measurement, even at currents up to 3000 A. Due to the rectangular shape, the Clamp on Tester is particularly suitable for busbars and cables with a large cross section. The Clamp on Tester adapter comes manufacturer calibrated with ISO calibration as an option.
- Measuring range: 1 A to 1000 A, 1 A to 2000 A, 1 A to 3000 A
- Transformer Ratio: 1 A / 1 mA, 2 A / 1 mA, 3 A / 1 mA
- Connection: 4 mm / 0.2 in socket

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-D34N

The CA-D34N D Series Clamp on Tester for oscilloscopes has a high-quality iron core with evenly distributed windings. This allows accurate AC current measurement, even at currents up to 3000 A. Due to the rectangular shape, the Clamp on Tester is particularly suitable for busbars and cables with a large cross section. The Clamp on Tester adapter comes manufacturer calibrated with ISO calibration as an option.
- Measuring range: 1 A to 500 A, 1 A to 1000 A, 1 A to 1500 A
- Transformer Ratio: 0.5 A / 1 mA, 1 A / 1 mA, 1.5 A / 1 mA
- Connection: 4 mm / 0.2 in socket

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-K1

Clamp on Tester for process streams up to max. 4.5 A, 3.9 mm diameter pliers, for multimeter.


- Range: 1 m A 4.5 A peak
- Measurement: AC A, DC A 

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-K2

Clamp on Tester for process streams up to max. 4.5 A, 3.9 mm diameter pliers, for multimeter.


- Range: 0.1 mA ... 450 mA peak
- Measurement: AC A, DC A

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-D37N

The CA-D37N D Series Clamp on Tester for oscilloscopes has a high-quality iron core with evenly distributed windings. This allows accurate AC current measurement, even at currents up to 3000 A. Due to the rectangular shape, the Clamp on Tester is particularly suitable for busbars and cables with a large cross section. The Clamp on Tester adapter comes manufacturer calibrated with ISO calibration as an option.
- Measuring range: 1 A to 30 A, 1 A to 300 A, 1 A to 3000 A
- Transformer Ratio: 1 A / 1 V, 100 A / 1 V, 1000 A / 1 V
- Connection: 4 mm / 0.2 in socket

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-D31N

The CA-D31N D Series Clamp on Tester for oscilloscopes has a high-quality iron core with evenly distributed windings. This allows accurate AC current measurement, even at currents up to 3000 A. Due to the rectangular shape, the Clamp on Tester is particularly suitable for busbars and cables with a large cross section. The Clamp on Tester adapter comes manufacturer calibrated with ISO calibration as an option.
- Measuring range: 1 A to 500 A, 1 A to 1000 A, 1 A to 1500 A
- Transformer Ratio: 0.5 A / 1 mA, 1 A / 1 mA, 1.5 A / 1 mA
- Connection: 4 mm / 0.2 in socket

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer