The PCE-830-2 Current Clamp is used for measuring one to three phases of electrical quantities for alternating current (AC). This Current Clamp also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

• PCE-830 + PCE-6802 amp clamp (1000 A)
• Electrical conductor pick-up: 55 mm / 2.1 in diameter
• Range selection: manual (10 A, 100 A, 1000 A)
• Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
• Sampling rate: 2 sec.
• Memory size: 512 kB (max. 52,000 values (single phase)

The easy-to-use PCE-PA 8300 Current Clamp is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

• Voltage measurement range of 10 V … 600 V AC
• Current measurement range of (Set 2) 30 A … 3000 A AC
• Performance measurement range of 0 kW … 9.999 MW (VA/VAR)
• Simultaneous display of harmonics and waveform
• Graphic Phasor diagram
• Captures transients including dip, swell, and outage

The easy-to-use PCE-PA 8300 Current Clamp is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

• Voltage measurement range of 10 V … 600 V AC
• Current measurement range of (Set 1) 20 A … 1200 A AC
• Performance measurement range of 0 kW … 9.999 MW (VA/VAR)
• Simultaneous display of harmonics and waveform
• Graphic Phasor diagram
• Captures transients including dip, swell, and outage

The PCE-830 Current Clamp is used for measuring one to three phases of electrical quantities for alternating current (AC). This Current Clamp also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm / 1.1 in diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
• Sampling rate: 2 sec.
• Memory size: 512 kB (max. 52,000 values (single phase)

The PCE-830-3 Current Clamp is used for measuring one to three phases of electrical quantities for alternating current (AC). This Current Clamp also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

• PCE-830 + PCE-3007 flexible amp clamp (3000 A)
• Electrical conductor pick-up: 170 mm / 6.69 in diameter
• Length of electrical conductor: 610 mm / 24.0 in
• Dimensions: 257 mm x 155 mm x 57 mm / 10.1 in x 6.1 in x 2.2 in
• Sampling rate: 2 sec.
• Memory size: 512 kB (max. 52,000 values - single phase)

The PCE-830 Current Clamp is used for measuring one to three phases of electrical quantities for alternating current (AC). This Current Clamp also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-6802 amp clamp (1000 A)
• Electrical conductor pick-up: 55 mm / 2.2 in diameter
• Range selection: manual (10 A, 100 A, 1000 A)
• Clamp dimensions: 244 x 97 x 46 mm / 9.6 x 3.8 x 1.8 in
• Incl. ISO calibration certificate

The PCE-830 Current Clamp is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Current Clamp also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 x 62 x 36 mm
• Incl. ISO calibration certificate

The PCE-830-3 Current Clamp is used for measuring one to three phases of electrical quantities for alternating current (AC). This Current Clamp also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-3007 flexible amp clamp (3000A)
• Electrical conductor pick-up: 170 mm / 6.7 in diameter
• Minimum radial curve: 35 mm / 1.4 in
• Length of electrical conductor: 610 mm / 24 in
• Sampling rate: 2 sec.
• Memory size: 512 kB / max. 52,420 data (1 phase)
• Incl. ISO calibration certificate

The PCE-360 is a Single-Phase Power Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

• Measuring range: 10 … 999.9 V
• AC voltage AC
• Alternating current AC
• Active power
• Power factor
• Phase angle
• Frequency
• Harmonic measurement
• Data memory: 512 kB   (non-volatile memory)
• incl. 4 current clamps / tapping terminals
• Standards: IP 30 / IEC 61 010, 600 V / CAT III
• incl. ISO Calibration Certificate

PCE-PA 8000 is a portable handheld power analyzer used for the testing and inspection of 3-phase / 4-wire, 3-phase / 3-wire, 1-phase / 2-wire and 1-phase / 3-wire electrical circuits. This handy power quality analyzer not only measures multiple electrical properties in real time, but also saves the measurement data in .xls format to the included SD card memory for quick and easy data transfer and analysis using Microsoft Excel.

• True RMS measurement for ACA, ACV
• True power: W, KW, MW
• VA, KVA, MVA, VAR, KVAR, MVAR
• PF (power factor), phase angle (Φ)
• KWH, KVAH, KVARH, PFH
• Voltage measurement range: 10 … 600 ACV
• Current measurement range: 0.2 … 1200 ACA
• Real-time current, voltage and power consumption measurement
• Built-in data recorder with adjustable sample rate: 2 … 7,200 sec.

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

• Measuring range: 10 … 999.9 V
• AC voltage AC
• Alternating current AC
• Active power
• Power factor
• Phase angle
• Frequency
• Harmonic measurement
• Data memory: 512 kB   (non-volatile memory)
• incl. 4 current clamps / tapping terminals
• Standards: IP 30 / IEC 61 010, 600 V / CAT III
• incl. ISO Calibration Certificate
• incl. ISO Calibration Certificate

PCE-PA 8000 is a portable handheld Current Clamp used for the testing and inspection of 3-phase / 4-wire, 3-phase / 3-wire, 1-phase / 2-wire and 1-phase / 3-wire electrical circuits. This handy power quality analyzer not only measures multiple electrical properties in real time, but also saves the measurement data in .xls format to the included SD card memory for quick and easy data transfer and analysis using Microsoft Excel.

• True RMS measurement for ACA, ACV
• True power: W, KW, MW
• VA, KVA, MVA, VAR, KVAR, MVAR
• PF (power factor), phase angle (Φ)
• KWH, KVAH, KVARH, PFH
• Voltage measurement range: 10 … 600 ACV
• Current measurement range: 0.2 … 1200 ACA
• Real-time current, voltage and power consumption measurement
• Built-in data recorder with adjustable sample rate: 2 … 7,200 sec.
• Incl. ISO Calibration Certificate

• alternating voltage: 40 ... 400 V
• alternating current: 2 ... 1250 A
• resolution: 0.01 V / 0.01 A
• active, apparent and reactive power
• electrical energy in Wh
• incl. app for Android
• 32 GB internal memory
• magnetic measuring adaptor

• alternating voltage: 40 ... 400 V
• alternating current: 3 ... 4800 A
• resolution: 0.01 V / 0.01 A
• active, apparent and reactive power
• electrical energy in Wh
• incl. app for Android
• 32 GB internal memory
• magnetic measuring adaptor

• alternating voltage: 40 ... 400 V
• alternating current: 2 ... 1250 A
• resolution: 0.01 V / 0.01 A
• active, apparent and reactive power
• electrical energy in Wh
• incl. app for Android
• 8 MB internal memory
• magnetic measuring adaptor
• incl. ISO-Calibration Certificate

• alternating voltage: 40 ... 400 V
• alternating current: 3 ... 4800 A
• resolution: 0.01 V / 0.01 A
• active, apparent and reactive power
• electrical energy in Wh
• incl. app for Android
• 8 MB internal memory
• magnetic measuring adaptor
• incl. ISO-Calibration Certificate

The Three-Phase Current Clamp (Graphic Power Quality Analyzer) PCE-GPA 62 is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics.

• Real-time test, register and measurement of voltage and current (real and effective) 
• Measures power factor and phase angle, frequency, energy, active, reactive and apparent power   (single-phase or three-phase in symmetrical networks). 
• Max. conductor diameter: 55 mm / 2.2 in
• Records up to 50,000 records

• alternating voltage: 40 ... 400 V
• alternating current: 0 ... 80 A
• resolution: 0.01 V / 0.01 A
• active, apparent and reactive power
• electrical energy in Wh
• incl. app for Android
• 32 GB internal memory
• magnetic measuring adaptor

• alternating voltage: 40 ... 400 V
• alternating current: 0 ... 80 A
• resolution: 0.01 V / 0.01 A
• active, apparent and reactive power
• electrical energy in Wh
• incl. app for Android
• 8 MB internal memory
• magnetic measuring adaptor
• incl. ISO-Calibration Certificate

This current clamp is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The current clamp is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

• Real-time test, register and measurement of voltage and current (real and effective) 
• Measures power factor and phase angle, frequency, energy, active, reactive and apparent power   (single-phase or three-phase in symmetrical networks). 
• Max. conductor diameter: 55 mm / 2.2 in
• Datalogger for 50,000 readings / software/ USB interface 
• incl. ISO Calibration Certificate

The device clamp force gage PCE-4PCFM is a 4-point force gauge that can ensure the optimal clamp force distribution. The force gage is used on device clamps for white and brown goods to avoid damage caused by incorrect force distribution.

• Measuring range: 30,000 N / 3,000 kg / 3 t
• Resolution: 10N / 1kg
• Measurement uncertainty: ±0.5% full scale
• Position of the 4 sensors is adjustable
• Touch display including printer
• Optional: Measurement data storage on USB stick

The device clamp force gauge PCE-4PCFM is a 4-point force gauge that can ensure the optimal clamp force distribution. The force gauge is used on device clamps for white and brown goods to avoid damage caused by incorrect force distribution.

• Measuring range: 30,000 N / 3,000 kg / 3 t
• Resolution: 10N / 1kg
• Measurement uncertainty: ±0.5% full scale
• Position of the 4 sensors is adjustable
• Touch display including printer
• Optional: Measurement data storage on USB stick

The current clamp is the ideal measuring device for measuring voltages up to 1500 V AC/DC and currents up to 1000 A AC/DC. The current measurement with the current clamp is inductive. To do this, the supply line is placed in the current clamp.

• Measuring range: 0 … 1500 V AC/DC
• Free app for Android and iOS
• Data logging for up to 100,000 measured values
• Inrush current measurement
• Insulation categories: CAT IV 600 V, CAT III 1000 V, CAT II 1500 V

• Voltage: 1 ... 1000V AC/DC
• Resolution: 0.1V
• Current: 0.5 ... 6000 A AC/DC
• Resolution: 0.1 A
• Accuracy: ±0.5% v.Mw.
• IEC 61000-4-30 Class A
• Frequency: 42.5 ... 460 Hz
• Power and energy
• Phase angle
• Harmonics
• Oscilloscope function
• Inrush current
• Efficiency measurement of inverters
• Mains signal monitoring
• Wifi
• Logger function and memory
• 7.8-inch touch display

• Voltage: 1 ... 1000V AC/DC
• Resolution: 0.1V
• Current: 0.5 ... 6000 A AC/DC
• Resolution: 0.1 A
• Accuracy: ±0.5% v.Mw.
• IEC 61000-4-30 Class A
• Frequency: 42.5 ... 460 Hz
• Power and energy
• Phase angle
• Harmonics
• Oscilloscope function
• Inrush current
• Efficiency measurement of inverters
• Mains signal monitoring
• Wifi
• Logger function and memory
• 7.8-inch touch display

The current clamp is the ideal measuring device for measuring voltages up to 1500 V AC/DC and currents up to 1000 A AC/DC. The current measurement with the current clamp is inductive. To do this, the supply line is placed in the current clamp.

• Measuring range: 0 … 1500 V AC/DC
• Free app for Android and iOS
• Data logging for up to 100,000 measured values
• Inrush current measurement
• Insulation categories: CAT IV 600 V, CAT III 1000 V, CAT II 1500 V
• incl. ISO Calibration Certificate