The Air Quality Station is specially designed for long-term monitoring of climatic conditions in, for example, offices, classrooms or lecture halls. The Air Quality Station is equipped with various sensors.
The air quality station is specially designed for long-term monitoring of climatic conditions in, for example, offices, classrooms or lecture halls. The air quality station is equipped with various sensors.
The air quality station is a multi-function meter for measuring the air quality. This Air Quality Station measures synchronously the CO2 concentration, the air temperature and the humidity.
The Air Quality Station is a multi-function meter for measuring the air quality. This Air Quality Station measures synchronously the CO2 concentration, the air temperature and the humidity.
- Measuring range CO2: 400 ... 5000 ppm - Measuring range temperature: -10.0 ... 50.0°C / 14 ... 122°F - Measuring range humidity: 0 ... 99% rh - Battery operation - Limit exceeded - Beep - incl. ISO Calibration Certificate (for CO2 only)
With the Air Quality Station you can ensure the right climate in your office. The Air Quality Station measures the CO2 content of the air, the relative humidity and the room temperature. The Air Quality Station shows carbon dioxide concentrations up to 9999 ppm, temperatures from -10… 50 °C, and relative humidity values from 20… 95%.
- Large CO2 measuring range up to 9999 ppm - Traffic light function for carbon dioxide - Measures temperature and humidity - Network operation - Suitable for classrooms, offices, lecture halls
With the Air Quality Station you can ensure the right climate in your office. The Air Quality Station measures the CO2 content of the air, the relative humidity and the room temperature. The Air Quality Station shows carbon dioxide concentrations up to 9999 ppm, temperatures from -10… 50 °C, and relative humidity values from 20… 95%.
- Large CO2 measuring range up to 9999 ppm - Traffic light function for carbon dioxide - Measures temperature and humidity - Network operation - Suitable for classrooms, offices, lecture halls - incl. ISO Calibration Certificate (for CO2 only)
The air quality station has a CO² measuring range of 0 ... 9999 ppm. In addition to the carbon dioxide measurement, the air quality station also has a carbon monoxide (CO) sensor with a measuring range of 0 ... 1000 ppm and a temperature and humidity sensor.
- Carbon monoxide (CO): 0 … 1000 ppm - Carbon dioxide (CO²): 0 … 9999 ppm - Temperature: 0 … 50 °C / 32 … 122 °F - Humidity: 0 … 100% RH - Data memory for 5000 measuring points - Data export CSV - Power supply: rechargeable battery
The air quality station is equipped with various sensors to determine HCHO, TVOC, ambient temperature and ambient humidity. The air quality station thus already covers a large spectrum of measuring tasks.
The Air Quality Station PCE-RCM 05 is used to continuously measure the particulate matter content at the workplace. The Air Quality Station displays PM2.5 particulate matter as well as temperature and humidity on the display.
- Measuring range PM2.5: 0 ... 500 μg / m³
- Measuring range temperature: -10 ... 50°C / 14 ... 122°F
- Measuring range humidity: 0 ... 99% rh
- Pictograms indicate air quality
- Battery operation
- Micro USB for charging
PCE-RCM 10 is a portable handheld air quality station or particle counter used to monitor particulate matter (PM) concentrations in the air. Designed to aid in indoor air quality (IAQ) assessments, this air quality station also measures air temperature and relative humidity (RH).
The Air Quality Station PCE-RCM 11 serves as an indicative test of environmental parameters. The Air Quality Station PCE-RCM 11 enables the measurement of fine dust, temperature and relative humidity. The bright display of the Air Quality Station provides information about the already mentioned parameters.
- Fine dust, formaldehyde, humidity, temperature, TVOC
- Particle size channels : PM 2.5 / PM 10
- Measuring range TVOC: 0.00 ... 9.99 mg / m³
(volatile organic compounds)
- Measuring range temperature: -20 ... 70°C / -4 ... 158°F
- Measuring range humidity: 0 ... 100% RH
- Measuring range formaldehyde: 0.00 ... 5.00 mg / m³
- Interface: USB
- For indicative measurements
The Air Quality Station is ideal for monitoring the air quality in homes, businesses or public buildings where people are staying. The 4.3-inch TFT display on the Air Quality Station is dimensioned so that all measured values can be read directly.
The Air Quality Station PCE-RCM 8 performs many measuring tasks. For example, the Air Quality Station can measure mass concentration, formaldehyde and TVOC. This Air Quality Station is specially designed for indoor measurement.
- Formaldehyde in mg / m³
- Measurement of TVOC
- Temperature measurement
- Alarm function
- Mass concentration
The Air Quality Station from PCE Instruments measures and stores the relevant measured variables: temperature, relative humidity, air pressure, light as well as acceleration in three axes by means of a vibration sensor. Therefore, this Air Quality Station is ideal for monitoring vibrations on machines while simultaneously measuring and recording the relevant environmental conditions of the system.
- 3-Axis acceleration up to 800 Hz
- 32 GB SD memory card
- Evaluation software
- Small design: 86.8 x 44.1 x 22.2 mm / 3.4 x 1.7 x 0.87 in
- Temperature, Humidity, Air pressure, Vibration, and Light
The Air Quality Station can be used in different fields of application. In use, the air flow meter carries out measurements from the smallest wind movements. The Air Quality Station can be used to monitor and alert on the current wind speed.
- Supply voltage: 230 V AC - Input signal: 4 ... 20 mA - 2 types of alarms - Sensor supply via evaluation device - Degree of protection: IP66 - Incl. ISO calibration certificate
The Air Quality Station can be used in different fields of application. In use, the air flow meter carries out measurements from the smallest wind movements. The Air Quality Station can be used to monitor and alert on the current wind speed.
- Air Quality Station with adjustable alarms - 2 alarm types - Supply voltage: 230 V AC - Input signal: 0 ... 10 V - Sensor supply via evaluation device - Degree of protection: IP66 - Incl. ISO calibration certificate
The Air Quality Station can be used in different fields of application. In use, the Air Quality Station carries out measurements from the smallest wind movements. The Air Quality Station can be used to monitor and alert on the current wind speed.
- Wind measuring device with adjustable alarms - 2 alarm types - Supply voltage: 115 V AC - Input signal: 4 ... 20 mA - Communication: RS485 - Sensor supply via evaluation device - Degree of protection: IP66 - Incl. ISO calibration certificate
The Air Quality Station can be used in different fields of application. In use, the Air Quality Station carries out measurements from the smallest wind movements. The Air Quality Station can be used to monitor and alert on the current wind speed.
- Wind measuring device with adjustable alarms - 2 alarm types - Supply voltage: 24 V DC - Input signal: 4 ... 20 mA - Sensor supply via evaluation device - Degree of protection: IP66 - Incl. ISO calibration certificate
PCE Instruments offers a wide range of stock products. However, despite an extensive selection of stock product offerings, sometimes a custom product is required to satisfy the specific requirements of a new, groundbreaking or special application.
Are you looking for custom test instruments?
Look no further than PCE Instruments. The DIN EN ISO 9001-certified PCE Product and Development Company GmbH produces customized test instruments tailored to meet the unique needs of a diverse customer base. By capitalizing on the expert knowledge and extensive experience of PCE’s industry-leading engineers and technicians to create custom-built test instruments, customers obtain measuring devices designed specifically for the task at hand.
Throughout the design, development and production process, PCE's engineers and technicians work hand-in-hand with each customer to ensure the final test instrument exceeds expectations. Specifications are clearly defined from the start of the project. Sensors, microprocessors and other electronic components are sourced from high-quality suppliers. Software is written to best support the customer's systems, processes and procedures. Qualified calibration laboratories are tasked with verifying the measurement accuracy of the custom test instrument, and rigorous testing is conducted to make certain that the device will function properly under the anticipated operating conditions.
If you are interested in pursuing the creation of a custom test instrument designed to accommodate an unusual or highly specialized measuring task, please contact the friendly and knowledgable staff at info@industrial-needs.com or +44 (0) 161-464902-5 for PCE Instruments UK, or at info@pce-americas.com or +1 (561) 320-9162 for PCE Americas Inc.
engineers and technicians to create custom-built test instruments, customers obtain measuring devices designed specifically for the task at hand.
