PCE-HVAC 3 is a multifunction thermometer or diagnostic measuring device used for indoor climate and environmental monitoring. In addition to measuring relative humidity and ambient room / dry-bulb temperature, the meter calculates dew-point and wet-bulb temperatures in degrees Celsius (°C) and Fahrenheit (°F). Thus, heating, ventilation and air conditioning (HVAC) installations and HVAC system performance assessments are key applications of the PCE-HVAC 3 meter.

- Relative humidity measuring range: 0 ... 100% RH
- Ambient / dew-point temp. range: -30 ... 100°C / -22 ... 212°F
- Wet-bulb temp. range: 0 ... 80°C / 32 ... 176°F

 

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

The multifunction psychrometer or diagnostic measuring device is used for indoor climate and environmental monitoring. In addition to measuring relative humidity and ambient room / dry-bulb temperature, the psychrometer calculates dew-point and wet-bulb temperatures in degrees Celsius (°C) and Fahrenheit (°F). Thus, heating, ventilation and air conditioning (HVAC) installations and HVAC system performance assessments are key applications of the psychrometer.

- Relative humidity measuring range: 0 ... 100% RH
- Ambient / dew-point temp. range: -30 ... 100°C / -22 ... 212°F
- Wet-bulb temp. range: 0 ... 80°C / 32 ... 176°F

PCE-LD 1 is a portable handheld refrigerant gas leak detector used to locate CFC/HFC refrigerant gas leaks. This highly sensitive gas leak detector can locate gas leaks from HVACR refrigeration systems even in areas contaminated by other gases. The gas sensor is located at the end of a 390 mm / 15.35 in flexible goose-neck tube, allowing unique access to hard-to-reach places.

- Adjustable high / low sensitivity:
    6 g/yr or 30 g/yr for R-22 and R-134a
    8 g/yr or 40 g/yr for R404A, R-407C and R-410A

 

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

The thermal / hot wire anemometer has a measuring range of up to 0 ... 30 m/s. In addition to the velocity, the thermal / hot wire anemometer can precisely measure the volume flow and temperature. The compact design of the sensors, in combination with the extendable telescopic probe, enable measurements to be taken even in places that are particularly difficult to access.

- Speed: 0.00 ... 30.00 m/s / 0.00 ... 98.42 ft/s
- Volume flow: 0.0 ... 339120.0 m3/h
- Temperature: 0 ... 50 °C / 32 ... 122 °F
- Telescopic probe length: 210 ... 426 mm / 8.2 ... 16.7"
- Telescopic probe diameter: 12 mm / 0.47"

The thermo-anemometer has a measuring range of up to 0 ... 30 m/s. In addition to the velocity, the thermo-anemometer can precisely measure the volume flow and temperature. The compact design of the sensors, in combination with the extendable telescopic probe, enable measurements to be taken even in places that are particularly difficult to access.

- Speed: 0.00 ... 30.00 m/s / 0.00 ... 98.42 ft/s
- Volume flow: 0.0 ... 339120.0 m3/h
- Temperature: 0 ... 50 °C / 32 ... 122 °F
- Telescopic probe length: 210 ... 426 mm / 8.2 ... 16.7"
- Telescopic probe diameter: 12 mm / 0.47"

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

- Measuring range: 0 ... 1250 μm / 0 ...  49.2 mils 
- Resolution: 1 μm / 0.039 mils
- Accuracy: ± (3% + 2 μm / 0.079 mils)
- Wear-resistant sensor
- V-groove for measurement on pipes

The configurable universal measuring transducer for electrical signals is a signal doubler and signal converter for process signals. A 4 ... 20-mA and 0 ... 10V DC signal can be applied to the input. The universal measuring transducer has 2 outputs, whereby output 1 can be set to 4 ... 20-mA and output 2 to 4 ... 20-mA or 0 ... 10V DC. It also has quadruple isolation between power supply, input signal, output 1 and output 2.

- Duplicates analog signals
- 4 ... 20-mA and 0 ... 10V
- Quick configuration using 2 buttons
- DIN rail mounting
- Inputs and outputs galvanically isolated
- Power supply 24 ... 250V AC/DC

The universal signal converter has an adjustable measuring range of 0… 600 V AC/DC and can therefore measure a wide variety of voltages. For example, it is possible to connect the transmitter to the supply line in order to monitor the applied voltage.

- Measuring range 0 ... 600 V AC/DC
- Active and passive output signal
- Display and keypad for configuration
- Frequency measurement
- DIN rail mounting
- Display

The configurable voltage measuring transducer for electrical signals is a signal doubler and signal converter for process signals. A 4 ... 20-mA and 0 ... 10V DC signal can be applied to the input. The universal measuring transducer has 2 outputs, whereby output 1 can be set to 4 ... 20-mA and output 2 to 4 ... 20-mA or 0 ... 10V DC. It also has quadruple isolation between power supply, input signal, output 1 and output 2.

- Duplicates analog signals
- 4 ... 20-mA and 0 ... 10V
- Quick configuration using 2 buttons
- DIN rail mounting
- Inputs and outputs galvanically isolated
- Power supply 24 ... 250V AC/DC

The voltage signal converter has an adjustable measuring range of 0… 600 V AC/DC and can therefore measure a wide variety of voltages. For example, it is possible to connect the transmitter to the supply line in order to monitor the applied voltage.

- Measuring range 0 ... 600 V AC/DC
- Active and passive output signal
- Display and keypad for configuration
- Frequency measurement
- DIN rail mounting
- Display

The voltage signal converter has an adjustable measuring range of 0… 600 V AC/DC and can therefore measure a wide variety of voltages. For example, it is possible to connect the transmitter to the supply line in order to monitor the applied voltage.

- Measuring range 0 ... 600 V AC/DC
- Active and passive output signal
- Display and keypad for configuration
- Frequency measurement
- DIN rail mounting
- Display

- AC / DC current, AC voltage and frequency measurement
- Integrated measuring point illumination
- Non-contact voltage tester
- Automatic range selection
- Forceps opening: 18 mm
- Automatic switch-off
- Incl. ISO calibration certificate

The wind measurer has a measuring range of up to 0 ... 30 m/s. In addition to the velocity, the wind measurer can precisely measure the volume flow and temperature. The compact design of the sensors, in combination with the extendable telescopic probe, enable measurements to be taken even in places that are particularly difficult to access.

- Speed: 0.00 ... 30.00 m/s / 0.00 ... 98.42 ft/s
- Volume flow: 0.0 ... 339120.0 m3/h
- Temperature: 0 ... 50 °C / 32 ... 122 °F
- Telescopic probe length: 210 ... 426 mm / 8.2 ... 16.7"
- Telescopic probe diameter: 12 mm / 0.47"