The main advantage of a steady-state stroboscope RT STROBE 5000 LED with intelligent LED-technology results from the absence of a short life xenon-tube, which is usually the first part which has to be replaced.

- Frequency range: 0…120,000 FPM
- Low-wear LED light trigger
- Illumination level 300 x 500 mm
- High intensity of light
- 120 LEDs

 

The main advantage of a steady-state stroboscope RT STROBE 5000 LED with intelligent LED-technology results from the absence of a short life xenon-tube, which is usually the first part which has to be replaced.

- Frequency range 0…120,000 FPM
- Low-wear LED light trigger
- Illumination level 300 x 500 mm
- High intensity of light
- 120 LEDs

 

The color meter PCE-CSM 3 was developed for quality control and inspection and offers a very high accuracy reading. You can choose between different color spaces (CIE L*a*b*C*h, CIE L*a*b*). After a measurement with the color meter, the reading can be stored as a reference value while other readings can be recorded as a sample and later be compared to the reference value easily. Delta pass/fail indication.

- CIE L*a*b*C*h or CIE L*a*b*
- Measuring geometry 8°/d
- White calibration disk
- Stores 100 reference values and 20,000 samples
- Measuring aperture is 8 mm
- Optional liquid sample kit listed under accessories

 

The color meter PCE-CSM 3 was developed for quality control and offers a very high accuracy reading. When using the color meter, you can choose between different color spaces (CIE L*a*b*C*h, CIE L*a*b*). After a measurement with these color test instruments, the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the 100 reference value easily.

The colorimeter PCE-CSM 3 was developed for quality control and offers a high accuracy. When using the colorimeter, you can choose between different color spaces (CIE L*a*b*C*h, CIE L*a*b*). After a measurement with the colorimeter, the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the reference value easily.

- CIE L*a*b*C*h, CIE L*a*b*
- Measuring geometry 8°/d
- White calibration standard included
- Stores 100 reference values and 20,000 samples
- Measuring aperture is 8 mm
- optional liquid sample kit listed under accessories

 

The paint test equipment was developed for quality control and offers a high accuracy. When using the paint test equipment, you can choose between different color spaces (CIE L*a*b*C*h, CIE L*a*b*). After a measurement with the paint test equipment, the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the reference value easily.

- CIE L*a*b*C*h, CIE L*a*b*
- Measuring geometry 8°/d
- White calibration standard included
- Stores 100 reference values and 20,000 samples
- Measuring aperture is 8 mm
- optional liquid sample kit listed under accessories

 

The Spectrophotometer PCE-CSM 3 was developed for quality control and offers a high accuracy. When using the Spectrophotometer, you can choose between different color spaces (CIE L*a*b*C*h, CIE L*a*b*). After a measurement with the Spectrophotometer, the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the reference value easily.

- CIE L*a*b*C*h, CIE L*a*b*
- Measuring geometry 8°/d
- White calibration standard included
- Stores 100 reference values and 20,000 samples
- Measuring aperture is 8 mm
- optional liquid sample kit listed under accessories

 

The colorimeter PCE-CSM 3 was developed for quality control and offers a high accuracy. When using the colorimeter, you can choose between different color spaces (CIE L*a*b*C*h, CIE L*a*b*). After a measurement with the colorimeter, the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the reference value easily.

- CIE L*a*b*C*h, CIE L*a*b*
- Measuring geometry 8°/d
- White calibration standard included
- Stores 100 reference values and 20,000 samples
- Measuring aperture is 8 mm
- Optional test box for liquid sample testing

 

  

- Measures Ra, Rz, Rq and Rt in Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.005 ... 16.00 μm / 0.197µinch... 629.921 µinch measurement range
- Rz, Rt: 0.002 ... 200.0 μm / 0.079µinch... 7874.016 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- Saves up to 20 Data points
- Micro-USB interface
- Built-in rechargeable li-ion battery
- Incl. ISO calibration certificate

 

  

- Measures Ra, Rz, Rq and Rt in Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.005 ... 16.00 μm / 0.197µinch... 629.921 µinch measurement range
- Rz, Rt: 0.002 ... 200.0 μm / 0.079µinch... 7874.016 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- Saves up to 20 Data points
- Micro-USB interface
- Built-in rechargeable li-ion battery
- Incl. ISO calibration certificate

The profilometer - roughness tester PCE-RT 1200-ICA is used to determine surface roughness. The compact profilometer is a handheld device for mobile use. Due to the power supply via a powerful battery, it can be used directly on site. The profilometer is used in the laboratory, in production and everywhere where the roughness of surfaces is to be determined.

- Measures Ra, Rz, Rq and Rt in Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.005 ... 16.00 μm / 0.197 µinch... 629.921 µinch measurement range
- Rz, Rt: 0.002 ... 200.0 μm / 0.079 µinch... 7874.016 µinch measurement range
- Induction method with Diamond sensor
- Large OLED display
- Display for the position of the probe
- Micro-USB interface
- incl. ISO Calibration Certificate

 

  

- Measures Ra, Rz, Rq and Rt in Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.005 ... 16.00 μm / 0.197µinch... 629.921 µinch measurement range
- Rz, Rt: 0.002 ... 200.0 μm / 0.079µinch... 7874.016 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- Saves up to 20 Data points
- Micro-USB interface
- Built-in rechargeable li-ion battery
- Incl. ISO calibration certificate

  

- Measures Ra, Rz, Rq and Rt in Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.005 ... 16.00 μm / 0.197µinch... 629.921 µinch measurement range
- Rz, Rt: 0.002 ... 200.0 μm / 0.079µinch... 7874.016 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- Saves up to 20 Data points
- Micro-USB interface
- Built-in rechargeable li-ion battery
- Incl. ISO calibration certificate

The durometer PCE-2900 has been developed for hardness measurements on metallic materials. The durometer PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The durometer PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission

The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission

 

The material hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The material hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The material hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission

The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission

The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission